preserve a piece of wood - Tilted Forum Project Discussion Community

Grancey · 10-18-2004, 06:59 PM

I found an interesting knotted piece of wood today when I was working outside. It's small, foot and a half. I would like to preserve it in the way that I've seen walking sticks done. Any know-how on this subject is appreciated.

2sheds · 10-19-2004, 12:34 PM

i'm not sure exactly what you're looking for, but you would probably want to coat it with some sort of clear protective film like polyurethane. you can buy polyurethane at home depot in the paint and finishes section. they sell it in cans you can brush or wipe on, and in spray cans. assuming your piece is somewhat odd-shaped, i'd suggest using a spray-on poly. minwax makes one. just go to home depot and ask for a "spray-on polyurethane" and you'll get the right stuff.

tips

1. make sure you clean the piece thoroughly first. any dirt or test will end up screwing up the finish

2. use several thin coats as opposed to one thick coat.

Grancey · 10-19-2004, 12:47 PM

Quote:

Originally Posted by 2sheds

i'm not sure exactly what you're looking for, but you would probably want to coat it with some sort of clear protective film like polyurethane. you can buy polyurethane at home depot in the paint and finishes section. they sell it in cans you can brush or wipe on, and in spray cans. assuming your piece is somewhat odd-shaped, i'd suggest using a spray-on poly. minwax makes one. just go to home depot and ask for a "spray-on polyurethane" and you'll get the right stuff.

tips

1. make sure you clean the piece thoroughly first. any dirt or test will end up screwing up the finish

2. use several thin coats as opposed to one thick coat.

I wasn't sure what I was looking for, because I didn't know where to start. But now I do. Thanks.

william · 10-22-2004, 04:55 PM

Polyurethane is a good protectant for wood. Make sure you sand it first. Also, if you want to change the color, there are plenty of stains available. Then use the poly as a good top-coat.
One final note - the closer to a "glass" look, the more you'll need to sand and paint (varnish, poly, etc.). Alternate the paint w/the sanding (fine grade or better).

10-18-2004, 06:59 PM	#1 (permalink)
Grancey Life's short, gotta hurry... Location: land of pit vipers	preserve a piece of wood I found an interesting knotted piece of wood today when I was working outside. It's small, foot and a half. I would like to preserve it in the way that I've seen walking sticks done. Any know-how on this subject is appreciated. __________________ Quiet, mild-mannered souls might just turn out to be roaring lions of two-fisted cool.

10-19-2004, 12:34 PM	#2 (permalink)
2sheds Crazy Location: dfw - texas	i'm not sure exactly what you're looking for, but you would probably want to coat it with some sort of clear protective film like polyurethane. you can buy polyurethane at home depot in the paint and finishes section. they sell it in cans you can brush or wipe on, and in spray cans. assuming your piece is somewhat odd-shaped, i'd suggest using a spray-on poly. minwax makes one. just go to home depot and ask for a "spray-on polyurethane" and you'll get the right stuff. tips 1. make sure you clean the piece thoroughly first. any dirt or test will end up screwing up the finish 2. use several thin coats as opposed to one thick coat. __________________ Depression is just anger without enthusiasm. It’s having an empty beer bottle but no one to throw it at.

10-22-2004, 04:55 PM	#4 (permalink)
william Psycho	Polyurethane is a good protectant for wood. Make sure you sand it first. Also, if you want to change the color, there are plenty of stains available. Then use the poly as a good top-coat. One final note - the closer to a "glass" look, the more you'll need to sand and paint (varnish, poly, etc.). Alternate the paint w/the sanding (fine grade or better).